JIS G3462 STBA24 Alloy Steel Seamless Boiler Tubes
- JIS G3462
- China
- Stock
- STBA24
JIS G3462 STBA24 Alloy Steel Tubes are mainly used for exchanging heat on within and in the vicinity of the underground. It can use as water tube, smoke tube, superheated tubes, air preheater tube, etc.
JIS G3462 STBA24 Alloy Steel Seamless Boiler Tubes
JIS G3462 STBA24 Alloy Steel Seamless Boiler Tubes
Standard: JIS G3462
JIS G3462 STBA24 Alloy Steel Tubes are mainly used for exchanging heat on within and in the vicinity of the underground. It can use as water tube, smoke tube, superheated tubes, air preheater tube, etc.Higher temperature resistance or capacity corrosion, end up being widely used by petroleum, chemical engineering, boiler, heat exchanger and other power areas.
JIS G3462 STBA24 alloy steel tube is not applicable for heating furnaces and heat exchangers for low temperature service.
JIS G3462 STBA24 Alloy steel boiler and heat exchanger tubes Quick Details
Type:Seamless.
Wall thickness(WT): 3.2mm——14 mm.
Outer diameter (OD): 19.05mm——168.3 mm
Length: 6M or specified length as required.
Ends: Plain End, Beveled End, Treaded
Additional Info
Port of Shipment: Tianjin, China
Payment Terms:T / T, LC
Delivery: 7-15 days after payment
Surface: Tubes will be varnished (Outside only) to prevent rust.
Marking: Standard + Steel Grade + Size + Heat No + Lot No
Package:Standard export package,suit for all kinds of transport, or as required
Method of Manufacture
The tubes of STBA24 shall be manufactured by seamless process.
The tube shall be subjected to heat treatments
| grade | Heat treatment |
| STBA 24 | Isothermal annealing, full annealing or normalizing followed by tempering |
Remark
1. Low temperature annealing shall not be applied to the electric resistance welded steel tube.
2. The tempering temperature for STBA 24 shall be 650˚ or higher
Chemical Composition of JIS G3462 STBA24
| Standard | Grade | Chemical Composition Limits (%) | ||||||
| C | Si | Mn | P | S | Cr | Mo | ||
| JIS G3462 | STBA24 | ≤ 0.15 | ≤ 0.50 | 0.30-0.60 | ≤ 0.030 | ≤ 0.030 | 1.90-2.60 | 0.87-1.13 |
Mechanical Properties of JIS G3462 STBA24
| Grade | Tensile Property (N/mm2) | Yield Point or Yield Strength (N/mm2) | Elongation (%) | ||
| OD ≥ 20 mm | 10 mm ≤ OD ＜20 mm | OD ＜10 mm | |||
| NO. 11 Sample; NO. 12 Sample | NO. 11 Sample | NO. 11 Sample | |||
| Longitudinal | Transverse | Transverse | |||
| STBA24 | ≥ 412 | ≥ 206 | ≥ 30 | ≥ 25 | ≥ 22 |
Note:
1. The above table is only applicable for heat exchanger alloy steel pipes. The buyer can appoint the upper limit value of tensile strength. The upper limit value of tensile strength is the above shown value plus 147 N/mm2.
2. For the alloy steel tube with the thickness of less than 8 mm, we use NO.12 sample for tensile test. The minimum elongation will be reduced by 1.5% from the table value when the thickness reduces 1 mm. The value obtained will be rounded to an integer value according to JIS Z 8401 (a rounding method).
3. When we take the electric resistance welded steel pipes for tensile test, we also choose NO.12 sample from the parts not containing welding seams.
The dimensional tolerances of tube shall be as follows:
(1)The tolerance on the outside diameter of the tube
Tolerances on Outside Diameter Unit: mm
| Division of outside diameter | Tolerances on outside diamete | |||
| Hot finished seamless steel tube | Cold finished seamless steel tube | Electric resistance welded steel tube other than cold finished | Cold finished electric resistance welded steel tube | |
| Under 25 |
+0.4 -0.8 |
【0.10 | 【1.5 | 【0.10 |
| 25 or over to and excl. 40 | 【0.15 | 【0.20 | 【0.15 | |
| 40or over to and excl. 50 | 【0.20 | 【0.25 | 【0.20 | |
| 50 or over to and excl 60 | 【0.25 | 【0.30 | 【0.25 | |
| 60 or over to and excl. 80 | 【0.30 | 【0.40 | 【0.30 | |
| 80 or over to and excl. 100 | 【0.40 | +0.40 | 【0.40 | |
| -0.60 | ||||
| 100 or over to and excl.12 |
+0.4 -1.2 |
+0.40 -0.60 |
+0.40 -0.80 |
+0.40 |
| -0.60 | ||||
| 120 or over to and excl.160 |
+0.40 -0.80 |
+0.40 -1.00 |
+0.40 | |
| -0.80 | ||||
| 160 or over to and excl.200 | +0.4 | +0.40 | +0.40 | +0.40 |
| -1.8 | -1.20 | -1.20 | -1.20 | |
| 200 or over | +0.4 | +0.40 | +0.40 | +0.40 |
| -2.4 | -1.60 | -1.60 | -1.60 | |
Note:For the tolerances on the outside diameter of electric resistance welded steel tube other than cold finished, if specially required by the purchaser, the tolerances on the outside diameter of cold finished steel tube may substitute.
(2)Tolerances on Wall Thickness and on Thickness Deviation
| Tolerances |
Division of wall thickness (mm) |
Division of method of manufacture | Hot finished seamless steel tube | Cold finished seamless steel tube | Electric resistance welded steel tube | |||
| Division of outside diameter (mm) | Under 100 | 100 or over | Under 40 | 40 or over | Under 40 | 40 or over | ||
| Tolerances on wall thickness % | Under 2 | --- | --- | +0.4mm |
+22 0 |
+0.3 |
+18 0 |
|
| 0 | 0 | |||||||
| 2 or over to and excl. 2.4 | +40 | --- |
+20 0 |
+18 0 |
||||
| 0 | ||||||||
| 2.4 or over to or excl. 3.8 | +35 | +35 | ||||||
| 0 | 0 | |||||||
| 3.8 or over to or excl. 4.6 | +33 | +33 | ||||||
| 0 | 0 | |||||||
| 4.6 or over | +28 | +28 | ||||||
| 0 | 0 | |||||||
|
Tolerances on thickness disparity % |
--- | Within 22.8 of wall thickness | --- | --- | ||||
Note:The "thickness deviation" means the ratio of the difference between the maximum and the minimum thickness of the wall measured in the same section to the ordered wall thickness and shall not be applied to the tube under 5.6 mm in wall thickness
(3)The Tolerance on length of the tube
| Division | Tolerance on length | ||
|
50 mm or under in
outside diameter
|
7 m or under in length | +0.7 mm | |
| 0 | |||
| Over 7 m in length |
Add 3 mm to the plus side permissible deviation given above for each increase of 3m or its fraction in length. However, the maximum value shall be 15 mm.
|
||
|
Over 50 mm in
outside diameter
|
7 m or under in length | +10mm | |
| 0 | |||
| Over 7 m in length |
Add 3 mm to the plus side permissible deviation given above for each increase of 3m or its fraction in length. However, the maximum value shall be 15mm.
|
||
Note:When accurate length is particularly required, the tolerances on it shall be agreed upon by the purchaser and the manufacturer.
W=0.2466 t (D-t)
where
W: unit mass of tube(kg/m)
t: wall thickness of tube(mm)
D: outside diameter of tube(mm)
Testing items:
Chemical Analysis, Tensile Test , Flattening test, Flaring test, Reverse Flattening Test , Hydrostatic Test or Nondestructive Examination.
Types of Packaging:
- Bundles (hexagonal)
- Wooden Boxes
- Crates (steel/wooden)
- Special crates for U-Bend tubes with each radius separated
- Alloy Seamless Steel Pipe packing can meet any needs of the customers.
Delivery: 15-25 days after payment
Product key description, this is a very good product description, detailing our product use, product characteristics